更新時間：2022-07-27
文章來源：http://www.r08sv.cn/
閱讀量：22
學校和單位大多組建報告廳音響系統，方便了自己使用，可是在報告廳音響在使用過程中沒有了聲音是一件讓人頭痛的事。下面就來講講相關原因。
Most schools and units have set up a sound system in the lecture hall, which is convenient for them to use. However, it is a headache that there is no sound in the use of the sound in the lecture hall. Now let's talk about the relevant reasons.
The sound in the lecture hall is silent
1.揚聲器接線斷開或分頻器異常
1. The loudspeaker wiring is disconnected or the frequency divider is abnormal
揚聲器接線斷裂后，揚聲器單元沒有激勵電壓，會造成無聲故障。分頻器一般不易斷線，但可能發生導線接頭脫焊、分頻電容器短路等故障。
After the speaker wiring is broken, the speaker unit has no excitation voltage, which will cause silent failure. The frequency divider is generally not easy to be disconnected, but the wire joint may be disconnected, and the frequency divider capacitor may be short circuited.
2.音圈斷
2. Broken voice coil
萬用表R可用×1檔測量揚聲器引出線焊片。如果電阻值為∞，可以用刀刮掉音圈兩端引線的密封漆，露出裸銅線后再測量。如果仍然不通過，則表示音圈內部斷線;如果測量已通過，則有\(zhòng)"喀喀\"聲音表說明音圈引線斷路，可以在線頭上焊接好，然后用另一段類似音圈繞線的漆包線焊接。
Multimeter r available × Measure the outgoing line solder of the loudspeaker in gear 1. If the resistance value is ∞, scrape off the sealing paint of the leads at both ends of the voice coil with a knife, expose the bare copper wire, and then measure. If it still fails, it means that the voice coil is broken inside; If the measurement has passed, there is a sound meter of "KaKa" indicating that the voice coil lead is open circuit, which can be welded on the wire head, and then welded with another section of enameled wire similar to voice coil winding.
3.揚聲器導線斷開
3. Speaker wire is disconnected
由于揚聲器紙盆振動頻繁，編織線容易斷裂，有時導線斷裂，但棉芯線仍保持連接。這種編織線不容易買到，可以用稍長的軟線代替。
Due to the frequent vibration of the loudspeaker paper basin, the braided wire is easy to break, and sometimes the wire breaks, but the cotton core wire remains connected. This kind of braided thread is not easy to buy and can be replaced by a slightly longer flexible cord.
4.音圈燒毀
4. Voice coil burned
用萬用表R×如果阻值接近0，1檔測量揚聲器引線Ω，且無\"喀喀\"聲音表明音圈燒壞了。更換音圈前，應磁間隙中的雜物，然后小心將新音圈放入磁間隙，糾正音圈，用強膠固定音圈的上下位置。音圈放置在佳位置后，用強膠填充音圈與紙盆之間的間隙，后密封防塵蓋，揚聲器紙盆向上，后正常使用。
Use multimeter R × If the resistance value is close to 0, measure the speaker lead Ω in gear 1, and there is no "click click" sound, indicating that the voice coil is burnt out. Before replacing the voice coil, remove the sundries in the magnetic gap, and then carefully put the new voice coil into the magnetic gap, correct the voice coil, and fix the upper and lower positions of the voice coil with strong glue. After the voice coil is placed in a good position, fill the gap between the voice coil and the paper basin with strong glue, seal the dust cover behind, and the speaker paper basin is upward. It will be used normally after one day.
有時沒有聲音有時又有聲音
Sometimes there is no sound, sometimes there is sound
1.揚聲器導線不良
1. Poor speaker wire
通常是由音圈引線發霉或焊接不良引起的。當紙盆振動頻繁時，斷點有時打開，有時斷開，形成不規則噪音時無故障。
It is usually caused by moldy voice coil leads or poor welding. When the paper basin vibrates frequently, the breakpoint sometimes opens and sometimes disconnects, and there is no fault when irregular noise is formed.
2.音圈引線斷線或即將短路。
2. The voice coil lead is broken or about to be short circuited.
3.功率放大器輸出插頭接觸不良或揚聲器輸入線斷線。
3. The output plug of power amplifier is in poor contact or the input line of loudspeaker is broken.
以上是關于報告廳音響無聲的原因的全部內容，如果您有相關的項目需求中有用到報告廳音響請聯系我們
http://www.r08sv.cn，為您提供好的幫助。
The above is all about the reason why the sound in the lecture hall is silent. Please contact us if you have relevant project needs that are useful for the sound in the lecture hall http://www.r08sv.cn , to provide you with good help.
魯公網安備 37010202002516號
